Advertisement

How to clean a washing machine that smells

A smelly washer usually needs more than a quick drum wipe. This walkthrough helps you find where the mildew smell is hiding, clean the right parts in the right order, and tell whether the odor is really gone.

Cleaning 8 min read
A front-load washing machine with the door open and the rubber gasket visible.
Advertisement

A smelly washing machine usually means residue, mildew, biofilm, trapped water, or a clogged drain path, not just a dirty drum. Clean the moisture-holding parts in the right order, and the steps differ for front-load and top-load washers. Start with the gasket or rim, then the drawer and drum, then the filter and drain area, and finish with a cycle that flushes out loosened buildup.

What the smell usually means

A musty or sour washer smell usually starts where water sits and detergent lingers. In a front-load washer, that’s often the rubber door gasket, the detergent drawer, or the pump filter area. In a top-load washer, the rim under the lid, the dispenser, the tub edges, and splash-prone crevices are the usual trouble spots.

If the machine smells worse right after a wash, check for standing water, a dirty filter, or a drain-path problem before blaming the laundry. If clothes come out damp-sour or musty even after a normal cycle, buildup inside the machine is a strong possibility. A drum can look clean and still smell bad if slime or residue is hiding in seams, folds, or traps.

What to check before you start

First, confirm whether you have a front-load washer or a top-load washer, because the cleaning targets are different. Front-loaders usually have a rubber door gasket and often a pump filter or access panel. Top-loaders usually don’t have a door seal, but they do collect grime under the lid, around the rim, and near the agitator or impeller.

Look for removable parts before you begin: a detergent drawer, fabric softener cup, lint filter, or access panel. Then check the owner’s manual for model-specific warnings, especially for the filter or pump trap. If the manual says not to use a certain cleaner on seals or finishes, follow that.

Also check where the water leaves the machine. If your washer has a hidden filter or trap, that’s often where the smell lives. If the odor seems like sewage rather than mildew, the washer may be pointing to a plumbing issue instead of a drum-cleaning problem.

What you need, and what to skip

You only need a few useful supplies: microfiber cloths, a small soft brush or old toothbrush, warm water, and one appropriate cleaner. Depending on the washer and the type of buildup, that cleaner might be a washer cleaner tablet or powder, oxygen bleach, or, in some cases, plain bleach. Use only what your machine manual allows.

Vinegar gets recommended a lot, but treat it as a mild deodorizing rinse rather than the main fix for heavy buildup. It can help with light odors, but it usually won’t remove a thick layer of biofilm on its own. Bleach can help sanitize if the manual allows it, but never mix it with vinegar, ammonia, or any other cleaner. Oxygen cleaner is useful for odor and organic residue when you want a non-chlorine option.

Skip abrasive pads, harsh scouring powders, and anything that can scratch the drum, gasket, or finish. Also skip pouring multiple cleaners together. That can be unsafe and can leave more residue behind than it removes.

Clean the gasket or top rim first

Start with the part that hides the most grime. On a front-load washer, pull back the door gasket folds and wipe out lint, hair, coins, and sludge. On a top-load washer, clean the lid rim, the underside of the lid, and the outer tub edge where splashback and soap residue collect.

  1. Open the washer and dry-wipe loose debris from the visible surfaces.
  2. On a front-loader, pull the gasket folds apart; on a top-loader, inspect the rim and lid area.
  3. Wipe with a damp microfiber cloth and a little cleaner, then scrub stubborn spots gently with a soft brush.
  4. Dry the area fully, including folds, seams, and the underside of the lid if your machine has one.

If you find black slime in the gasket folds or a sticky film on the rim, don’t move on too fast. That buildup is a common odor source, and the smell usually comes back if you leave it there.

A person wiping grime from the rubber door gasket inside a front-load washing machine.

Clean the drawer, drum, and visible buildup

Next, clean the soap drawer and the drum. Remove the detergent drawer if your model allows it, rinse it, and scrub the channels where detergent and softener turn gummy. If there are removable inserts, wash those too and let them dry before reinstalling.

  1. Pull out the detergent drawer and rinse away loose residue.
  2. Scrub the drawer, inserts, and housing with warm water and a soft brush.
  3. Wipe the drum, door glass, and any visible soap film.
  4. For a front-load washer, wipe around the inner lip where water can sit after the cycle.
  5. For a top-load washer, wipe the agitator or impeller area and the inside tub walls.
  6. Run an empty hot cycle with the cleaner your manual allows.

A hot cycle helps loosen residue, and B&Q recommends a 60°C cycle at least once a week to break down residue and kill bacteria. If you use a washer cleaner, follow its label. If you use bleach, only do so if your manual allows it. The first empty hot cycle often loosens buildup, but the real fix is the wiping you did before and after it.

Clean the filter and drain path

If the smell is still hanging around, check the filter or pump trap next. On some washers, lint, coins, hair, and sludge collect there and keep the machine smelling sour. Whirlpool notes that a clogged pump filter can hold debris and that you should check your owner’s manual for the model-specific cleaning method.

  1. Unplug the washer or turn it off before opening any access panel.
  2. Find the filter, pump filter, or trap location in the manual.
  3. Place towels and a shallow tray or pan under the area if water may spill out.
  4. Remove debris, lint, coins, and any visible sludge.
  5. Wipe the housing clean and close the panel securely.

If there’s standing water or a drain area that smells like sewage, stop there and inspect the drain path, hose, or plumbing connection. That isn’t usually a drum-cleaning problem anymore. It may be a clog or vent issue outside the washer itself.

A person opening the pump filter area of a washing machine to remove trapped lint and debris.

Run the finishing cycle and check the result

After the hidden parts are clean, run one more empty rinse or hot cleaning cycle if your manual recommends it. The point is to flush out loosened residue, cleaner, and anything you missed. Then leave the door or lid open so the inside can dry fully.

You’ll know it worked when the washer smells neutral at the door. The gasket or rim should no longer leave residue on a white cloth, and the next load should come out clean-smelling instead of musty. A clean washer should not smell sour as soon as you open it.

If the odor is still there after cleaning the gasket, drawer, drum, and filter, the problem is likely outside the washer or in a model-specific part you haven’t reached yet.

How to keep the smell from coming back

The habits that matter most are simple. Take wet clothes out promptly, because damp laundry left sitting is a fast way to get a smelly washing machine. Leave the door or lid open after use so the interior can dry, and wipe the gasket or rim if water pools there.

Use less detergent than you think you need, especially if you use HE detergent in an HE machine. Too much soap leaves residue that feeds odor. Run a hot wash regularly if your manual allows it; B&Q recommends a 60°C cycle at least once a week to help break down residue and reduce bacteria.

Keep an eye on the drawer, filter, and gasket. A quick monthly wipe is easier than another full odor cleanup later. If the smell starts returning right after a wash, check for trapped water or a filter problem before you assume the laundry is the cause. If your washer model has a filter that can be cleaned, Whirlpool says to follow the owner’s manual for the model-specific method.

Frequently Asked Questions

Can I use vinegar to clean a washing machine that smells?

Yes, for light odor control, but it usually works best as a mild cleaner or rinse rather than the only fix. If the washer has mildew, sludge, or heavy biofilm, clean the gasket, drawer, filter, and drain path first. Then use a hot cycle with a washer cleaner your manual allows.

Should I clean a front-load washer differently from a top-load washer?

Yes. Front-loaders usually need close attention to the door gasket, drawer, and pump filter area, while top-loaders usually need the lid rim, underside, tub edge, and agitator or impeller area. The drum cleaning step is similar, but the hidden grime lives in different places.

Sources